long board roof decking

Buy 96mm EcoTherm Eco-Deck is a tough, structural thermal composite board for flat roofs, comprising a 90mm PIR insulation core faced with 6mm exterior The board should be fixed to joists set at a maximum of 600mm centres, with the timber side uppermost and the board laid with the long edge running along the joist.

For wood plank decks, the existing nailing has generally proven to be adequate (If at least two nails were installed every time one of the planks crossed a rafter or truss) so you should not need to re-nail the deck. For wood panel sheathing (plywood or Oriented Strand Board, OSB) nail sizes and nail spacing commonly used, 

Problems with roof sheathing often don't appear until tear-off. And new shingles just don't last as long over existing shingles due to the increased heat build-up in the mass of asphalt. Heat is asphalt's number one enemy, and the The issue, Guertin explains, is the gaps between boards. On older homes 

We are often asked, why do we need plywood over our old solid sheathing? The keyword here is “solid.” It used to be standard to use shiplap, 1″ boards, tongue & groove, or other boards for the roof deck. These 8 to 12-inch wide boards were nailed together tight. plywood_1 When the roof was first nailed on, of course all 

SterlingOSB RoofDek is a sanded tongued and grooved board designed specifically for flat roof decking and pitched roof applications. Designed to Engineered specifically for roofing applications, the tongued and grooved panels remove the need for noggins or dwangs by providing structural support at long edges.

Best options for a stable roof deck and smooth shingle surface are plywood, OSB and wood boards. The outside layers are longitudinally arranged to increase the strength and stiffness in the direction of the alignment, that is, the long direction across the rafters or trusses. OSB is available for structural 

ROOF DECK SUBSTRUCTURES. CHAPTER 6. 6. INTRODUCTION. The roof substructure is an integral part of the roof system. It lies just beneath the metal . plank roof decks are typically used where their appearance from inside the building is a primary consideration. The boards may be solid lumber or laminated boards.

Oriented Strand Board isn't plywood, nor is it a type of particleboard, fiberboard or wafer board, and although it is a newcomer to a plywood-dominated market, Both the National Roofing Contractors Association and the Asphalt Roofing Manufacturers Association recommend the use of OSB for roof sheathing, as long as it 

9 30 2014. 10. Wood Roof Sheathing Options. Wood Structural Panels. Oriented Strand Board (OSB) and Plywood. Solid Sawn Decking. 2x, 3x and 4x dimensional lumber. Mechanically Laminated or Tongue & Groove. Panel Products: Structural Insulated Panels (SIPS). Cross-Laminated Timber (CLT) 

edges or on long edges only. Note: Each cavity to have unobstructed ventilation. Ceiling lining. Vapour control layer. Insulation with ventilation space over. Wood-based board decking. Waterproofing membrane. (with reflective finish). Figure 2.6: Typical cold deck flat roof a: roof covering, b: roof deck, c: ventilated air space, 

Superior Thermal Barrier. DensDeck provides superior fire resistance — better than wood fiberboard, perlite, high-density polyisocyanurate or gypsum fiberboards. Increase the total fire rating of the assembly… by using DensDeck as a thermal barrier over the roof deck AND as a cover board under the membrane.

The plywood was fastened through the rigid foam to the rafters with long screws. . If your roof has board sheathing, install an airtight membrane (for example, Solitex Mento, a product available from 475 High Performance Building Supply), a layer of synthetic roofing underlayment, or a peel-and-stick 

I beat the ants but it took a long time. Did the roof Photograph 1 (above left): Original Roof Uninsulated rafter framing with board roof deck. Furring straightens out rafter plane New shingles were installed over a fully adhered membrane applied directly to the original roof decking. Then the first winter 

METDECK is the WARM ROOF Solution. The METDECK Warm Roof Solution consisting of insulated decking board for long strip copper and zinc standing seam roofing utilising the high performance of Kingspan Kooltherm technology.. The Layers: METDECK Upper Face is an 18mm FSC Certified WBP exterior grade 

The number of nails needed for a roof varies on multiple factors, such as board face width, length and roof truss spacing. Boards used for sheathing range from those with a 4-inch face to 48-inch-long plywood sheets. A structure's roof truss spacing can vary from every 12 to 24 inches. Each of these factors 

The highest uplift forces occur at roof corners, edges, and ridge lines. □ Improved fasteners such as ring shank nails increase the uplift resistance of the roof sheathing. Sheathing Type. Typically, 15 32-inch or thicker panels are required in high- wind areas. Oriented Strand Board (OSB) or plywood can be.

The framer used 2” nails to install the roof sheathing with 5” to 8” o.c. spacing. While there is no provision for use of 2” nails in the International Residential. Code, the ICC-ES Evaluation Report ESR-1539 from the. International Staple, Nail and Tool Association does allow for a 0.099” diameter, 2-1 4” long deformed-.

Follow these simple construction steps for roof sheathing to ensure optimal performance and minimize callbacks. Step 1: Always Check for a Level Nailing Surface. This can be done with a straight piece of lumber (6 feet to 10 feet long) or a long carpenter's level. Trusses or rafters should be shimmed as necessary to provide 

roofing material, but also the entire wood deck or sheathing beneath the roofing. In older garages, the sheathing is usually made of “1-by” planking (1 x 6, 1 x 8, 1 x10, or 1 x12. #2 grade pine). The high price of wood planking will probably have you looking for a less expensive alternative for this job. Particle board is not a 

Product Details

Product List